MATLAB XPC TARGET 4 - API GUIDE Guía de usuario Pagina 147
- Pagina / 372
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using xpctarget.fs Objects
7-9
Using xpctarget.fs Objects
The fs object enables you to work with the target PC file system. The fs object
has methods that allow you to use
•
cd to change directories
•
dir to list the contents of the current directory
•
diskinfo to get information about the current disk
•
fclose to close a file (similar to MATLAB fclose)
•
fileinfo to get information about a particular file
•
filetable to get information about files in the file system
•
fopen to open a file (similar to MATLAB fopen)
•
fread to read a file (similar to MATLAB fread)
•
fwrite to write a file (similar to MATLAB fwrite)
•
getfilesize to get the size of a file in bytes
•
mkdir to make a directory
•
pwd to get the current working directory path
•
removefile to remove a file from the target PC
•
rmdir to remove a directory
Useful global utility:
•
readxpcfile, to interpret the raw data from the fread method
The procedures in this section assume that the target PC has a signal data file
created by an xPC Target scope of type
file. This file has the pathname
C:\data.dat.
This section includes the following topics:
• “Accessing File Systems from a Specific Target PC” on page 7-10
• “Retrieving the Contents of a File from the Target PC to the Host PC” on
page 7-11
• “Removing a File from the Target PC” on page 7-13
• “Getting a List of Open Files on the Target PC” on page 7-14
- User’s Guide 1
- How to Contact The MathWorks: 2
- Embedded Option 6
- Troubleshooting 10
- Function Reference 11
- Contents 12
- Target and Scope Objects 13
- 1 Target and Scope Objects 14
- Scope Objects 15
- Targets and Scopes in the 19
- MATLAB Interface 19
- Working with Target Objects 20
- Deleting Target Objects 21
- 2 Alternatively, you can type 22
- Working with Scope Objects 25
- 2 Alternatively, type 26
- Signals and Parameters 37
- 3 Signals and Parameters 38
- Monitoring Signals 39
- Signal Tracing 47
- Add Target Scope 49
- Add to Scopes 53
- Software Triggering Scopes 57
- Scope of Type Host 69
- Scope of Type Target 69
- Interrupted) or finishes 71
- Signal Logging 75
- Signal logging 75
- Enter key 81
- Parameter Tuning with MATLAB 83
- Simulation menu, click 87
- Connect to target 87
- Configure button 93
- Add to table 93
- Update Parameter button 95
- 4 Embedded Option 100
- 9 Boot the target PC 103
- *.rtb file 105
- Embedded Option Setup 107
- Creating a DOS System Disk 109
- Create BootDisk 111
- DOSLoader Target Setup 111
- Reset button on your target 113
- Stand-Alone Target Setup 115
- Software Environment 123
- 1 In the MATLAB window, type 124
- Explorer 125
- Command-Line Interface 128
- In the MATLAB window, type 129
- Using the Target PC 131
- C. In this case 132
- Target PC 133
- System: S0 has value 5.1851 134
- Working with Target PC 139
- Files and File Systems 139
- Introduction 140
- FTP and File System Objects 142
- Using xpctarget.ftp Objects 143
- Using xpctarget.fs Objects 147
- Graphical User Interfaces 155
- 8 Graphical User Interfaces 156
- Host PC Target PC 157
- To xPC Target Block 159
- Block Parameters 161
- Signal Properties 165
- Documentation tab 165
- Interface 169
- Web Browser Interface 170
- Ctrl+C by 172
- Ctrl+C is not used to 172
- Using the Main Pane 174
- Main pane 175
- Changing WWW Properties 177
- -1 or Inf 178
- 1, enter 180
- Interrupts Versus Polling 181
- 10 Interrupts Versus Polling 182
- Polling Mode 183
- Target Application 189
- Polling Mode Performance 193
- 11 xPC Target and Fortran 196
- Prerequisites 197
- Compiling Fortran Files 201
- Parameters 205
- 12 Troubleshooting 210
- Is the Target PC Halted? 211
- Create Bootdisk 219
- Advanced Troubleshooting 223
- Can Library parameter in 225
- PCI Slot parameter of 225
- Target PC Command-Line 235
- Interface Reference 235
- Target PC Commands 236
- Target Object Methods 237
- Scope Object Methods 239
- or move mouse 243
- 14 Function Reference 246
- Target Objects 247
- Functions — Categorical List 251
- 14addscope 253
- Syntax MATLAB command line 253
- Arguments 253
- MATLAB command line 258
- Purpose Remove target object 260
- function 262
- 14fc422mexcalcbits 265
- 14get (scope object) 272
- AutoRestart check box to 273
- Number of samples, then 273
- 14get (target object) 281
- 14getxpcenv 297
- Syntax MATLAB Command Line 297
- RAM size 298
- Target boot mode 304
- Purpose Reboot target PC 312
- 14set (scope object) 320
- Description 320
- 14set (target object) 329
- Simulation 331
- 14setxpcenv 334
- Interface” on page 5-6 342
- Target PC command line 345
- 14updatexpcenv 352
- 14xpcexplr 355
- 14xpctarget.fs 356
- 14xpctarget.ftp 358
- 14xpctarget.xpc 360
- MATLAB Command Line 364
- 14xpcwwwenable 365
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales